Entry 003 · Flux, horns, and 0402s

Cleaning the board, wicking the horns, and placing parts the size of a grain of sand.

A cleanup with 99% isopropyl and a soft brush, peaked solder horns taken down with copper wick, and eight 0402 resistors placed on the last practice column.

The board was still cloudy from the last session, with flux dried wherever it had run out from the joints. I wanted to see what I had actually done before I went any smaller, so I started by cleaning it.

Cleaning off the flux

I used 99% isopropyl alcohol and a soft-bristle electronics brush, and worked over the residue around the 0603 column I had already soldered, including the pads for R34 through R38 and the nearby lamp-side footprints. The cloudy film came up more easily than I expected, and the soldermask underneath was suddenly readable again.

Aikokkl LP050 · live view Rec
Microscope view of the practice board before cleaning, with a cloudy white film of flux residue around the R34–R38 pads and the nearby D10, D11, D17, R58, R59, and R66 footprints.
The R34 column and the nearby lamp pads, still filmed over with flux from the last session.
Aikokkl LP050 · live view Rec
Microscope view after cleaning, showing six 0603 resistors marked 1001 in the R34–R39 column and a column of tan 0603 capacitors at C13–C18, several of them sitting tilted with peaked solder on the right-hand pads. The 0402 column on the far right is still empty.
After the 99% isopropyl and a soft brush: the residue around R34 through R38 is gone, and the 0603 capacitors are easier to judge, which is not entirely a comfort.

The joints underneath

With the flux gone, it was harder to talk myself into thinking the 0603 capacitors at C13 through C18 were fine. Several of the parts sit tilted on the pads, and the solder on the right-hand ends rises into peaks instead of wetting the termination and lying down. The parts are only getting smaller, so it felt like time to re-evaluate how I was putting the solder down.

Aikokkl LP050 · live view Rec
Low-angle view of the 0603 resistor and capacitor columns, with tall peaked spikes of solder standing up from the terminations, and the empty 0402 pads along the right edge of the board.
From a low angle, the extra solder on both 0603 columns turns into horns, which is a clearer picture than the view from above.

Copper wick

I have copper desoldering braid in the kit, and this was the point at which I started getting more comfortable using it. The idea was not to make the joints look finished, and not to chase a perfect fillet just yet. I wanted the horns gone, and the aim for now is still just to pass a continuity check, not to make the work look pretty.

The method that worked for me was straightforward. I used a fresh end of braid, put a little flux on it, laid that end flat on the joint, and rested the iron on top of the braid rather than trying to poke at the solder directly. Once the solder melted and wicked up into the copper, I lifted the braid and the iron together so I would not dump a blob back onto the pad, and then clipped off the used section.

Aikokkl LP050 · live view Rec
Microscope view of copper desoldering braid held in tweezers over the board, with the used end frayed and darkened, above the 0603 resistors at R35–R40 and the capacitors at C15–C19, whose solder peaks are lower than before.
The braid after a few of those joints, held over the 0603 columns. The horns are lower, which is as far as I was trying to take it.

A grain of sand

I moved on to the last resistor column, the 0402s, which are absolutely ridiculously tiny. Before I started, I wanted a photograph for scale, and I grabbed the wrong parts. At this size the packages look almost alike, and the first fingertip shot was of the 0603 resistors I had already been using. The real 0402s are smaller still, and truly grain-of-sand like: about 1.0 by 0.5 millimeters.

Aikokkl LP050 · live view Rec
A small black 0603 resistor resting on the pad of a pinky fingertip, with more loose resistors scattered on the blue silicone mat beside it.
The first scale shot, which I only later realized was a 0603. I had picked up the wrong pile because the two sizes are easy to confuse when they are both this small.
Aikokkl LP050 · live view Rec
A much smaller 0402 resistor on a fingertip, with a few equally tiny loose parts visible at the edge of the blue mat.
The part that actually belongs in the last column, which is about the size of a grain of sand.

I fluxed the 0402 pads along the T6 column and tinned each one with the least amount of solder I could manage, just a small bump on one pad of each footprint, with no parts on the board yet. Then I held each resistor in place, tacked the tinned side, and soldered the other end the same way, a tiny bit of solder at a time.

The 0402 column at T6, with a little bump of solder on each pad and nothing placed yet.
Aikokkl LP050 · live view Rec
Low-angle close-up of the empty 0402 column, where small shiny bumps of solder stand on one pad of each footprint, with the T6 test points in the foreground.
The same bumps from a low angle, which is about as little solder as I could put down on purpose.

The first one went on, not perfectly, but it was on. After that I leaned heavily on the microscope to sit the next parts, and I’m getting more used to working under it instead of trying to place them by naked eye. The second and third sat a little straighter than the first.

Aikokkl LP050 · live view Rec
Microscope view of the top of the 0402 column, with the first resistor tacked onto its pads and the footprints below it still empty except for small solder bumps.
The first 0402, tacked on one side. It isn’t sitting as flat as I would like, but it is on the pads.
Aikokkl LP050 · live view Rec
Microscope view of the first three 0402 resistors placed in the column, with cloudy flux residue on the soldermask around them and the fourth footprint still empty.
The second and third, seated under the microscope, which I’m learning to trust more than my unaided eye at this size.

I got eight of them on the board. The rest disappeared, and I think I swept them off with my arm when I leaned down on the mat. I could not find them again, which, at the size of a grain of sand, is easy to believe.

Aikokkl LP050 · live view Rec
Microscope view of the 0402 column with eight tiny resistors placed, flux residue still visible on the board, and the blue mat filling the rest of the frame.
Eight 0402s in place, which is where I stopped after the remaining parts went missing.

I did get a reading across the ones I had placed, 132.5 to 132.6, and that was enough. I am satisfied and humbled by the exercise.

132.5 ohms across the eight 0402s I had on the board, held on the 200 ohm range.

Leaning over parts that small for that long left my neck and back tight, so I went for a walk to work the tension out. It felt like the right way to close the session.

What’s next

The lamp circuit is still ahead, and I’ll photograph the joints as I go, including the ones I would rather retake.

Next: Something I forgot to mention before my last post: we have a fan system now. →

← Previous: Soldering the first columns on parts smaller than they look.

← Back to the journal